Plumbing Essentials: A Prerequisite for When Installing a Bathtub
Plumbing Essentials: A Prerequisite for When Installing a Bathtub
Blog Article
In this article below you can find some brilliant insights related to A Step-by-Step Guide to Installing a Bathtub.
Setting up a bath tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bathtub with a brand-new one is likewise a reasonably challenging job. If the old tub is conveniently easily accessible, the project can relocate immediately; if you have to open up a wall surface to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either instance, the project is within a home handyman's skills, although you will require a helper to leave the old bathtub and also set in the new one. Make certain you have actually certified on your own for the work and also are comfortable attempting it. Instead of working with a service provider to take over a halfway-completed task, it is far better to take into consideration using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly help you mount a brand-new tub in your bathroom if you have already gotten a new tub and don't need to alter the setup of your previous water pipelines.
Your tools and also material list need to make up the following:
Planning for the Installment
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to make certain that if the faucet features a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets system to stop stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps using 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you use every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with new ones as a part of your setup, then the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain any kind of water remaining in the system. The procedure of removing the existing taps can be fairly problematic due to the restricted access that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the continuing to be water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from transforming throughout this procedure. When the faucets have been removed, the holes in the bath/basin will have to be cleansed of any old securing compound.
Before carrying on to fit the new taps, contrast the pipeline links on the old faucets to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Utilizing both wood boards under its feet, place the tub in the needed position. The wood boards are helpful in uniformly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 tiny points.
The following objective is to ensure that the bath tub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the bathtub till the level reads level.
To install faucets, fit all-time low of the outermost adaptable tap connector to the ideal supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the water and check all joints and also new pipework for leakages and tighten them if required. Load the bath tub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the tub should wait up until the bathtub has been used a minimum of when as this will resolve it into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, then you will need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making sure that the washers are in location in between the faucet as well as the sink. Safeguard the faucet in position with the producer supplied backnut. When the faucet is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical faucet ports. The previous type ought to be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to split a rigid seal, creating the water to pass through the wall between the bathroom and the tiling, leading to difficulties with moisture and possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and also fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly fill the tub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealer can break fairly early if you do not take into consideration this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily available on the market. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very eager about How to Install a Bathtub and I am assuming you appreciated the blog entry. Are you aware of anybody else who is sincerely interested in the niche? Do not hesitate to share it. I value reading our article about How to Install a Bathtub.
Toilet issues? Call! Report this page